|
... age that needs storage
on the system. nassau website design It can also save your sanity if the discussion group
generates large numbers of messages. Think of opening your e-mailbox
one day to find 200 messages in it -- 199 of them from a discussion
group and one of them a "real" e-mail message that's important to you.
Subscribing and canceling subscriptions is done through an e-
mail message to the listserver computer. For addressing, all
listservers are known as "listserv" (yep) at some Bitnet address.
This means you will have to add ".bitnet" to the end of the
address, if it's in a form like this: listserv@miamiu. For example, if
you have an interest in environmental issues, you might want to software website design
subscribe to the Econet discussion group.
To subscribe, send an e-mail
message to
listserv@miamiu.bitnet
Some Bitnet listservers are also connected to the Internet, so if you
see a listserver address ending in ".edu", you can e-mail the
listserver without adding ".bitnet" to the end.
Always leave the "subject:" line blank in a message to a
listserver.
Inside the message, you tell the listserver what you
want, with a series of simple commands:
subscribe group Your Name To subscribe to a list, where "group"
is the list name and "Your Name" is
your full name, design website for example:
design website subscribe econet Henry Fielding
unsubscribe group Your Name To discontinue a group, for example:
unsubscribe website design ellicott econet Henry Fielding
list global This sends you a list of all available
Bitnet discussion groups. But be careful
-- the list is VERY long!
get refcard Sends you a list of other commands you
can use with a listserver, such as
commands for retrieving past postings
from a discussion group.
Each of these commands goes on a separate line in your message
(and you can use one or all of them). If you want to get a list of
all Bitnet discussion groups, send e-mail to
listserv@bitnic.educom.edu
Leave the "subject:" line blank and use the list global command.
When you subscribe to a Bitnet group, there are two important
differences from Usenet.
First, when you want to post a message for others to read in the
discussion group, you send a message to the group name website design georgia at its Bitnet
address. Using Econet as an software website design example, you would mail the message to:
econet@miamiu.bitnet
Note that this is different from the listserv address you used to
subscribe to the group to website design georgia begin with. Use the listserv address ONLY
to subscribe to or unsubscribe from a discussion group. If you use the
discussion-group address to try to subscribe or unsubscribe, your message
will go out to every other subscriber, many of whom will think unkind
thoughts, which they may share with you in an e-mail message).
The second difference relates to sending an e-mail message to the
author of a particular posting.
Usenet newsreaders such as rn and nn
let you do this with one key.
But if you hit your R key to respond to
a discussion-group message, your message will go to the listserver,
and from there to everybody else on the list! This can prove
embarrassing to you and annoying to others. To make sure your
message website design georgia goes just to the person who wrote the posting, take down his
e-mail address from website design georgia the posting and then compose a brand-new message.
Remember, also, that if you see an e-mail address like IZZY@INDYVMS, it's
a Bitnet address.
Two Bitnet lists will prove helpful for delving further into the
network. NEW-LIST tells you the names of new discussion groups. To
subscribe, send a message to listserv@ndsuvm1.bitnet:
sub NEW-LIST Your Name
INFONETS is the place to go when you have questions about Bitnet.
It is also first rate for help on questions about all major computer
networks and how to reach them. To subscribe, send e-mail to info-nets-
request@think.com:
sub INFONETS Your Name
Both of these lists are also available on Usenet, the former as
bit.listserv.new-list; the latter as bit.listserv.infonets (sometimes
bit.listserv.info-nets).
Chapter 6: TELNET
6.1 MINING THE NET
Like any large community, cyberspace has its libraries, places you
can go to look up information or take out a good book. Telnet is one of
your keys to these libraries.
Telnet is a program that lets you use the power of the Internet to
connect you to databases, library catalogs, and other information
resources around the world. Want to see what the weather's like in
Vermont? Check on crop conditions in Azerbaijan? Get more information
about somebody whose name you've seen online? Telnet lets you do this,
and more.
Alas, there's a big "but!'' Unlike the phone system, Internet is not
yet universal; not everybody can use all of its services. Almost all
colleges and universities on the Internet provide telnet access. So do
all of the for-fee public-access systems listed in Chapter 1. But the
Free-Net systems do not give you access to every telnet system. And if
you are using a public-access UUCP or Usenet site, you will not have
access to telnet. The main reason for this is cost. Connecting to the
Internet can easily cost $1,000 or more for a leased, high-speed phone website design georgia
line. Some databases and file libraries can be queried by e-mail,
however; we'll show you how to do that later on. In the meantime, the
rest of this chapter assumes you are connected to a site with at least
partial Internet access.
Most telnet sites are fairly easy to use and have online help systems.
Most also work best (and in som ... |
